DSpace Collection: ผลงานการเขียนบทความทางวิชาการของอาจารย์คณะวิศวกรรมศาสตร์ มหาวิทยาลัยศรีปทุมผลงานการเขียนบทความทางวิชาการของอาจารย์คณะวิศวกรรมศาสตร์ มหาวิทยาลัยศรีปทุมhttp://dspace.spu.ac.th/handle/123456789/842024-03-29T09:25:29Z2024-03-29T09:25:29ZA New Simple Method for Post-tension Strands Friction Coefficient MeasurementChatr Suchindahttp://dspace.spu.ac.th/handle/123456789/45712016-09-24T12:40:39Z2014-08-27T00:00:00ZTitle: A New Simple Method for Post-tension Strands Friction Coefficient Measurement
Authors: Chatr Suchinda
Abstract: This article describes a new simple method of measuring the friction coefficients and their values
from construction sites in Thailand. The friction coefficients between prestressing strands and their conduits
are related to both wobble and curvature. The method requires both measured jacking force and elongation
of each strand so the average tensile force along the entire length can be determined from non-linear
stress-strain relationship. Then, the total length and total curvature of each strand were calculated from shop
drawing to simulate the friction calculation in the design process. The determined friction coefficients will
include the effect due to misplace of the conduit layouts from shop drawings. From the experimental measurement
of 624 bonded system strands with spiral galvanized metal sheet conduits in post-tensioned slabs
structures from two construction sites with two different post-tensioned sub-contractors, the wobble coefficient
is 0.0035 per foot and the curvature coefficient is 0.536 per radian for sub-contractor 1 and the wobble
coefficient is 0.0040 per foot and the curvature coefficient is 0.578 per radian for sub-contractor 2. The friction
coefficients significantly differ than those recommended by ACI318-11 and BS8110-1997 standards.
Description: International Conference Paper2014-08-27T00:00:00Zวิธีอย่างง่ายวิธีใหม่ในการวัดค่าสัมประสิทธิ์แรงเสียดทาน สำหรับลวดอัดแรงดึงทีหลังฉัตร สุจินดาhttp://dspace.spu.ac.th/handle/123456789/42362018-06-08T08:48:53Z2013-05-09T00:00:00ZTitle: วิธีอย่างง่ายวิธีใหม่ในการวัดค่าสัมประสิทธิ์แรงเสียดทาน สำหรับลวดอัดแรงดึงทีหลัง
Authors: ฉัตร สุจินดา
Abstract: บทความนี้กล่าวถึงวิธีการวัดค่าสัมประสิทธิ์แรงเสียดทานที่เกิดขึ้นระหว่างลวดอัดแรงชนิดตีเกลียวและท่อร้อยลวด ทั้งแบบที่เกิดจากความคดและความโค้ง โดยการเก็บค่าแรงดึงของลวดที่ปลายที่ดึงลวด และระยะยืดของลวดแต่ละเส้น เพื่อนำมาใช้หาค่าแรงดึงเฉลี่ยตลอดความยาวเส้นลวดจากสมการความสัมพันธ์ของระหว่างหน่วยแรงและหน่วยการยืดตัวของเส้นลวดแบบเชิงเส้นไม่ตรง และคำนวณความยาวและความโค้งรวมของลวดแต่ละเส้นจากแบบก่อสร้าง เพื่อให้เหมือนกับการคำนวณในขั้นตอนออกแบบ และได้ค่าสัมประสิทธิ์ที่มีการปรับแก้ความเพี้ยนของตำแหน่งการวางลวดเมื่อเทียบกับแบบก่อสร้างไว้แล้ว จากการทดลองวัดและคำนวณค่าดังกล่าวของเส้นลวดอัดแรงที่ใช้ท่อร้อยลวดสำหรับอัดฉีดน้ำปูนเพื่อให้เกิดแรงยึดเหนี่ยวชนิดที่ม้วนตีเกลียวมาจากแผ่นเหล็กชุบสังกะสีจำนวน 470 เส้น จากสถานที่ก่อสร้างจริง พบว่าได้สัมประสิทธิ์ความคดมีค่าเท่ากับ 0.0035 ต่อฟุต (1.758 ต่อเมตร) และได้ค่าสัมประสิทธิ์ความโค้งมีค่าเท่ากับ 0.536 ต่อเรเดียน ซึ่งค่าทั้งสองมากกว่าที่แนะนำไว้ในมาตรฐาน ACI318-11 อย่างมีนัยสำคัญ
This article describes the new method of measuring the friction coefficient between prestressing strands and their conduits which are related to both wobble and curvature. The method requires both measured jacking force and elongation of each strand so the average tension along the entire length can be determined from non-linear stress-strain relationship. The total length and total curvature of each strand were calculated from shop drawing to simulate the friction calculation in the design process. The determined friction coefficients will include the effect due to misplace of the conduit layouts. From the experimental measurement of 470 bonded system strands with spiral galvanized metal sheet conduits from the actual construction site, the wobble coefficient is 0.0035 per foot (1.758 per meter) and the curvature coefficient is 0.536 per radian. Both coefficients are significantly higher than those recommended by ACI318-11 standard.
Description: Conference Paper2013-05-09T00:00:00Zการเพิ่มประสิทธิภาพเครื่องกัดแผ่นวงจรพิมพ์โดยใช้การควบคุมอุณหภูมิเพชร นันทิวัฒนาhttp://dspace.spu.ac.th/handle/123456789/25882016-09-24T12:09:25Z2554-08-17T08:43:23ZTitle: การเพิ่มประสิทธิภาพเครื่องกัดแผ่นวงจรพิมพ์โดยใช้การควบคุมอุณหภูมิ
Authors: เพชร นันทิวัฒนา2554-08-17T08:43:23ZFlux/underfill Compatibility Study for Flip-chip Assembly ProcessPhuthanate Phoosekieaw and Sanya Khunkhaohttp://dspace.spu.ac.th/handle/123456789/24412016-09-24T12:04:55Z2011-05-28T00:00:00ZTitle: Flux/underfill Compatibility Study for Flip-chip Assembly Process
Authors: Phuthanate Phoosekieaw and Sanya Khunkhao
Abstract: The rapid uptake of flip-chip technology within the electronics industry due to their better thermal performance, smaller size, lower profile, light weight, and higher input/output density, the solder
joints together with underfill in flip chip package serve as a mechanical mechanism for resisting the thermal deformation induced by the coefficient of thermal expansion (CTE) mismatch between silicon die and substrate. underfill materials are employed in flip-chip assemblies to enhance solder joint reliability performance. The adhesion of underfills with solders is important to the integrity of the flip-chip structure. The effect of temperature and humidity aging as well as flux residue on adhesion strength was also investigated.2011-05-28T00:00:00Z